Juberafab portfolio

[juberafab]

Figured I would start a JuberaFab thread for all the projects and stuff we make / build. Some of the stuff to look forward to in the thread...
CNC Machining
Truck Builds
CAD Work
Sheet Metal Work
Offroad Stuff 😂
GoKart Stuff

 

[juberafab]

We're currently running another batch of our swaybar arms after after hours 😂.
First op is completed on all 14.
We're currently in the process of sourcing tooling to do the spline broaching in-house. This batch is all 35 spline out of 6061 aluminum.

 

[juberafab]

Here is a picture of some custom accessory brackets for a LS based motor in one of the center mount truck we are building.

 

[juberafab]

Here are our father son project we are working on. 2 seater go cart. We put a HF 420 motor in it with a 40 series clutch. We also widened the chassis to fit the RZR seats. We took it out to sunfair a week ago and it rips. The kids have been having a blast riding it around the property. Our son has had a blast working on it and learning.

 

[Dirt Yota]

That’s epic! Lucky kids!!!! Following this for the awesomeness of the many projects!

 

[juberafab]

Ano

That’s epic! Lucky kids!!!! Following this for the awesomeness of the many projects!

Thanks. I am lucky that are kids are into as much as we are. Go cart has been down cuz we are waiting for a belt and the kids have been bummed. LOL I am going try and update it more often than not. Lol

 

[juberafab]

Some upper arms we are going to prototype for our CM kits.

 

[juberafab]

Clearance is clearance. Mocking up the alternator on the CM tube chassis Expo. Running out of room quick.

 

[juberafab]

Some fully fabricated d44 knuckles we built for the expo we built a few years ago. These are specifically made to allow a custom machined rotor hat to accept a 14 inch rotor with 6 piston will wood calipers. He recently took it down to Mexico and pit it through it paces. We love it when are parts get tested and used. No issues as well.

 

[juberafab]

Front view

 

[the bodj]

Having parts fit like that looks like so much fun to weld

 

[juberafab]

Having parts fit like that looks like so much fun to weld

It was nice. I tacked them in the fixture and pre heated them before welding. Welds layed in super nice. chromoly is always a pleasure to weld.

 

[theycallmeWALLY]

It was nice. I tacked them in the fixture and pre heated them before welding. Welds layed in super nice. chromoly is always a pleasure to weld.

I was just going to ask you about pre-heating before welding.

What's your process on something big/thick like that? do you stick it in an oven so everything stays clean or???

 

[juberafab]

I was just going to ask you about pre-heating before welding.

What's your process on something big/thick like that? do you stick it in an oven so everything stays clean or???

I put them into the jig and preheated in my small powder coat oven up to around 400* . Once I remove it I do the first pass making sure not to over heat the material.. While it is still hot I will make the second or wash pass where needed and then let it slowly cool. If needed you can put it into a bucket of sand and cover it to allow it to cool slow or cover it with a welding blanket.

 

[mobil1syn]

are the sprindles something you are going to offer in the future?

 

[juberafab]

are the sprindles something you are going to offer in the future?

We plan too. I have had some interest but the price factor isn't that appeasing. LOL just the big brake kit is costly. 6 piston calipers and 14 inch rotors add up.
We will be making a 2wd race setup with lift built into the knuckles set up for 2.5 hubs, big brakes and uniballs. This setup will be going on a beamed tundra we built recently.