JRI Gen1 Raptor

JACKSONRALLYINC

Well-known member
Joined
Mar 15, 2023
Messages
143
Location
Sage, CA
The time has come for a modern~ish family adventure-mobile. We have been thinking Raptor for a little over a year now and the time came for us to scoop one up. We ended up with this 2014 with 88k miles on the clock and a bit of bolt-on work done to it. I really wanted a bone stocker but had a tough time finding a low mileage one. I was a bit hesitant to buy a truck that had some work done to it, I prefer to buy stock and do my own thing, however this one popped up and seemed to have decent parts so we went with it.

2014 Raptor
88k Miles
ADD Mid-Travel front with Fox 3'' Internal Bypass, I believe this kit is discontinued (not a fan of it and will likely build my own)
Rear Deavers (leafs party harder)
Rear 3'' Fox 3 Tube Bypass
Rear (unknown make) Bump Stop Kit with Fox Bumps
37's
Methods
4.88 gears
Rear ADD bumper (will be up for sale soon)
ADD "Chase Rack" (will be up for sale soon)
Magnum side steps (will be up for sale soon)
Seems to have had as bunch of misc work done to it over the last 5 years. New steering rack, plugs, shock rebuild (didn't do the bumps) claims to have replaced the "ball joints'' but it has uniballs, loose ones at that. Upper arms are bushed and loose, seems to have had a winch at one point and the wiring was cut and abandoned. Has a SCT (I think) tuner/controller, claims it is to fix the speedo after putting on the 37's and the re-gear. All in all we are happy, the truck needs love all over the place but we are happy with it. Oh, it seems to keep eating SDHQ cv boots on the passenger inner, not sure what is going on but I will figure it out.

I do not have any glamour shots at this time, but here is "The Long Way Home" Raptor

20250906_143527 (1).jpg20250906_093907.jpg
 
I have been reading up on the other Gen1 threads and want to take this time to thank folks for their threads, postings and knowledge. I hope I can contribute some knowledge with my thread here.
 
We have had the Raptor for about 8 days now, I feel like I need a good month to go through things and get parts on order. Here are some shots of the stuff someone bolted on and some shit limit strap tabs :oops:

20250911_174054.jpg20250911_174046.jpg20250910_161025.jpg20250910_160909.jpg20250910_160904.jpg20250910_160901.jpg20250907_183044.jpg
 
Last edited:
Damn. Upper arm and limit strap mount look like they’ve seen some better days 🤣

You’ve done such badass work in the past, can’t wait to see what this looks like.
 
Records indicate the shocks were rebuilt 6k miles ago. I think one of the fronts may have been re-assembled incorrectly. I looked on Fox's website for a manual and I could only find the installation guide, anyone know where to get a parts diagram or the like? I can do the re-build but I do not want to pull both off at the moment to compare side to side. I am not sure how to explain it but I am getting a weird diagonal (left rear to right front) bobble, very unsafe at highway speeds. It feels like a dead spot in the R front. I believe they are can in can IBP? I wonder if it is possible to put the can in upside down?
 
You can't put the IBP sleeve in upside down. It simply will not seal up. The seal head is machined to fit the sleeve only in the correct orientation. The front gen 1 shocks are super weird. removing and setting the IFP is a trick in it self that not a lot of people know how to do correctly. If they set the IFP correctly, and everything was re sealed correctly, only thing i could think of is they didn't add the correct amount of oil and there is air in the system, but even that is hard to do because the seal head has bleed screws to release any trapped air. Sucks to say but the best way to do it is pull them back apart and double check. Also check to make sure both coilovers are on the same "perch", there is low, mid and high. Sometimes the springs will either be assembled in the wrong perch side to side, or the spring could be cracked. that happens a lot as well.
 
Last edited:
Back
Top