Baconcreekmetal's latest activity

  • B
    Baconcreekmetal reacted to HTO's post in the thread Carly's 96 with Like Like.
    Setup my tie rods. I found out afterward i have 1.25 tube to sleeve since the 1.5 is .120 wall so ill remake the two long ones. Its...
  • B
    Baconcreekmetal reacted to HTO's post in the thread Carly's 96 with Like Like.
    Okay the swinger is done. Bolts are shanked and oil impregnated bronze bushings are pressed in. Tomorrow will be tube for the tie rods.
  • B
    Baconcreekmetal reacted to HTO's post in the thread Carly's 96 with Like Like.
    Got the pitman arm done. I need to cut new swinger plates and then on to tie rods.
  • B
    Baconcreekmetal reacted to HTO's post in the thread Carly's 96 with Like Like.
    Started the steering mock up. I'm thinking I need to paint the tie rods to look like the pvc and add some hose clamps once I make a set.
  • B
    Baconcreekmetal reacted to HTO's post in the thread Carly's 96 with Like Like.
    Also, the drivers beam is done. I’ve always liked the look of the hammered paint.
  • B
    Baconcreekmetal reacted to HTO's post in the thread Carly's 96 with Like Like.
    Had some down time so I chipped away some more. Got the cage bolted in and the bump mount in also. The heater hose hard line will be...
  • B
    Baconcreekmetal reacted to HTO's post in the thread Carly's 96 with Like Like.
    I got a wild hair and wanted to see the bump in its home. It should work pretty well I think.
  • B
    Baconcreekmetal reacted to HTO's post in the thread Carly's 96 with Like Like.
    The last of the pictures from yesterday. All in all a productive weekend. Hopefully I'll get some more time soon. For now, its time...
  • B
    Baconcreekmetal reacted to HTO's post in the thread Carly's 96 with Like Like.
    Got the inner fender cut out including the coilover spot. Radius arms are done brackets are painted and only 1 bolt left on drivers side...
  • B
    Baconcreekmetal reacted to HTO's post in the thread Carly's 96 with Like Like.
    Not too shabby. I believe it’ll hold up.
  • B
    Baconcreekmetal reacted to HTO's post in the thread Carly's 96 with Like Like.
    Been a minute, but the engine cage is done. Hopefully I'll be able to get the front bump mounts boogered up so reassembly can happen.
  • B
    Baconcreekmetal reacted to HTO's post in the thread Carly's 96 with Like Like.
    got the shock mount wrapped with plate so now u need to stop procrastinating and cut the rivets off the driver's side. I seriously hate...
  • B
    Baconcreekmetal reacted to HTO's post in the thread Carly's 96 with Like Like.
    So setup bearings are done. Spent time with my knock off Dremel but it did the job and now once the shims and spider gears come in I can...
  • B
    Baconcreekmetal reacted to HTO's post in the thread Carly's 96 with Like Like.
    So a few packages showed up. Two more to go. Yes I'm going to attempt a regear on my own. I have the Dana 44 service manual and a how to...
  • B
    Baconcreekmetal reacted to HTO's post in the thread Carly's 96 with Like Like.
    Okay got the shock mount rotated. I am clearing the frame rails by just over 1.5" so all in all I'm good with that. I'll take it all...
Show older items
Back
Top